Im fairly settled on Klipsch PRO-6504-L-THX in-walls for the FR/FL and Klipsch PRO-7800-L. Hi Folks, Im in the process of configuring my new houses media room for a 7.1.4 Atmos setup and I could use some help from the wise folks here. This setup includes four ceiling-mounted speakers and seven channels with two surrounds placed at either side, two at the rear, and three front channels. Please refer to the user manual of the respective model.ĭolby Atmos speaker configurations with top (ceiling) speakers are not compatible to Auro-3D. (Edited) 7.1.4 Atmos In-Wall & In-Ceiling Speaker placement help. Though there are many ways to layout Dolby Atmos setup 4, explained below, are the best positions for ceiling speakers.AV Receivers indicated with an asterisk will need an additional external power amplifier for such a 7.1.4 configuration. The AV Receier will automatically switch on the speakers that can be used in the current surround mode. With the AVR-X4300H*, AVR-X4400H*, AVR-X6200W*, AVR-X6300H, AVR-X6400H and AVR-X7200W(A)* as well as AVC-X8500H, you can add Surround Back speakers as well (7.1.4) that will not work in Auro-3D, but will be supported in Dolby Atmos, DTS:X and Auro-2D Surround (2D upmixing mode of Auro-3D). Im not going to put that many speakers in yet but I want to put in the speaker wires in for future proofing before I install the drywall. The Voice of God (Top Surround) is not supported in configurations using Dolby speakers. I have the Dolby Atmos 9.1.2 Speaker Placement but I was wondering if there is a similar setup guide for 11.2 speaker layout. Note that this functionality may require a firmware update of your AV Receiver. a system consisting of Front Dolby and " Su rround Dolby or Back Dolby" speakers is then fully compatible to Auro-3D and Dolby Atmos as well as DTS:X. Rounding the math slightly, this suggests the ceiling speakers are 50' to 125' in front of and behind the listening position. Note that support for Dolby Atmos in both 5.1.2 and 7.1.4 configurations is limited to MacOS Monterey. The Dolby Atmos theater installation guide PDF suggests that in a 7.1.4, the ceiling speakers be 30 - 55 degrees from the listening position, with sight-line to the screen being 0 degrees. These are some of the things I am concerned about. I hope I made myself clear in what I am trying to explain. With AVR-X4400H, AVR-X6400H and AVC-X8500H, you are able to use Dolby Atmos enabled speakers for Auro 3D 9.1 playback as well, i.e. Finally, click configure speakers on the bottom right-hand corner and configure the aggregate device for 7.1.4 Dolby Atmos. 1) Move left and right side surround speakers into the ceiling as well, along with the atmos speakers (keeping 7.1.4 setup) 2) Get rid of them all and move to a 5.1.4 setup. This 9.1 (5.1.4) configuration is then fully compatible to Auro-3D and Dolby Atmos as well as DTS:X. Surround Height speakers won't work for Dolby Atmos as they aren't defined in Atmos specification.įor the models AVR-X4200W, AVR-X4300H, AVR-X4400H, AVR-X6200W, AVR-X6300H, AVR-X6400H and AVR-X7200W(A) as well as AVC-X8500H, it is possible to use Rear Heights instead of Surround Heights for Auro-3D playback. Today on Daily HiFi, we discuss where to place your surround speakers in a 7.1.4 Dolby Atmos Home Theater. Besides the ability to playback Auro-3D content the Auro-3D speaker configurations allows playback of Dolby Atmos content with at least 7.1ch (Floor 5.1ch + Front Height) speakers.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |